cf14f55043
Set IPA low/med/high bandwidth mbps threshold to higher number in ini cfg for sdm845 target to achieve higher throughput. Change-Id: I44386e1ef67d014a4bc79345b455422c75c4b03f CRs-Fixed: 2516770
668 lines
18 KiB
INI
668 lines
18 KiB
INI
# This file allows user to override the factory
|
|
# defaults for the WLAN Driver
|
|
|
|
# gVersion needs to be increased once the parameters in this file is changed
|
|
# in order to update the ini file from /vendor/etc/wifi/ into /data/misc/wifi folder.
|
|
gVersion=12.0.1
|
|
|
|
# Enable IMPS or not
|
|
gEnableImps=1
|
|
|
|
# Enable BMPS or not
|
|
gEnableBmps=1
|
|
|
|
# Phy Mode (auto, b, g, n, etc)
|
|
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
|
|
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
|
|
# 7 = 11b only 8 = 11ac only.
|
|
gDot11Mode=0
|
|
|
|
# Assigned MAC Addresses - This will be used until NV items are in place
|
|
# Each byte of MAC address is represented in Hex format as XX
|
|
Intf0MacAddress=000AF58989FF
|
|
Intf1MacAddress=000AF58989FE
|
|
Intf2MacAddress=000AF58989FD
|
|
Intf3MacAddress=000AF58989FC
|
|
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
|
InfraUapsdVoSrvIntv=0
|
|
InfraUapsdViSrvIntv=0
|
|
InfraUapsdBeSrvIntv=0
|
|
InfraUapsdBkSrvIntv=0
|
|
|
|
# Flag to allow STA send AddTspec even when ACM is Off
|
|
gAddTSWhenACMIsOff=1
|
|
|
|
# Flags to filter Mcast and Bcast RX packets.
|
|
# Value 0: No filtering, 1: Filter all Multicast.
|
|
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
|
|
McastBcastFilter=3
|
|
|
|
#Flag to enable HostARPOffload feature or not
|
|
hostArpOffload=1
|
|
|
|
#Flag to enable HostNSOffload feature or not
|
|
hostNSOffload=1
|
|
|
|
# 802.11n Protection flag
|
|
gEnableApProt=1
|
|
|
|
#Enable OBSS protection
|
|
gEnableApOBSSProt=1
|
|
|
|
#Enable/Disable UAPSD for SoftAP
|
|
gEnableApUapsd=1
|
|
|
|
# Fixed Rate
|
|
gFixedRate=0
|
|
|
|
# Maximum Tx power
|
|
# gTxPowerCap=30
|
|
|
|
# Fragmentation Threshold
|
|
# gFragmentationThreshold=2346
|
|
|
|
# RTS threshold
|
|
RTSThreshold=1048576
|
|
|
|
# Intra-BSS forward
|
|
gDisableIntraBssFwd=0
|
|
|
|
# WMM Enable/Disable
|
|
WmmIsEnabled=0
|
|
|
|
# 802.11d support
|
|
g11dSupportEnabled=1
|
|
|
|
# 11d host offload
|
|
ignore_fw_reg_offload_ind=1
|
|
|
|
# 802.11h support
|
|
g11hSupportEnabled=1
|
|
|
|
# DFS Master Capability
|
|
gEnableDFSMasterCap=1
|
|
|
|
# ESE Support and fast transition
|
|
EseEnabled=1
|
|
|
|
ImplicitQosIsEnabled=0
|
|
|
|
# If AP signal is changing quickly (like in warehouse), cannot wait 200 seconds to trigger scan
|
|
gNeighborScanTimerPeriod=200
|
|
gRoamRestTimeMin=50
|
|
#200 to 5 for roaming scan
|
|
gNeighborLookupThreshold=85
|
|
gNeighborScanChannelMinTime=20
|
|
gNeighborScanChannelMaxTime=30
|
|
gMaxNeighborReqTries=3
|
|
|
|
# Roaming requirement states that we must perform roam scan by default every 5 seconds while RSSI is low
|
|
#gNeighborScanRefreshPeriod=5000
|
|
|
|
# If no candidate is found, perform another scan after 5 seconds
|
|
# Rapid scanning will drain battery and doesn't make sense since AP conditions don't change that quickly
|
|
# Also, '0' might mean that if no candidate is found, then scan is not refreshed at all
|
|
gEmptyScanRefreshPeriod=5000
|
|
|
|
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
|
# To enable, set FastRoamEnabled=1
|
|
# To disable, set FastRoamEnabled=0
|
|
FastRoamEnabled=1
|
|
|
|
# Check if the AP to which we are roaming is better than current AP in
|
|
# terms of RSSI. Checking is disabled if set to Zero.Otherwise it will
|
|
# use this value as to how better the RSSI of the new/roamable AP should
|
|
# be for roaming
|
|
RoamRssiDiff=5
|
|
|
|
# To enable, set gRoamIntraBand=1 (Roaming within band)
|
|
# To disable, set gRoamIntraBand=0 (Roaming across band)
|
|
gRoamIntraBand=0
|
|
|
|
#Short Guard Interval Enable/disable
|
|
gShortGI20Mhz=1
|
|
gShortGI40Mhz=1
|
|
|
|
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
|
|
gAPAutoShutOff=0
|
|
|
|
#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
|
|
gWlanAutoShutdown = 0
|
|
|
|
# Not used.
|
|
gApAutoChannelSelection=0
|
|
|
|
#Preferred band (both or 2.4 only or 5 only)
|
|
BandCapability=0
|
|
|
|
#Channel Bonding
|
|
gChannelBondingMode5GHz=1
|
|
gChannelBondingMode24GHz=1
|
|
|
|
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
|
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
|
|
#is idle for last 10 seconds.) For both active and power save clients.
|
|
|
|
#Power save clients: DUT set TIM bit from 10th second onwards and till client
|
|
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
|
|
|
|
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
|
|
#success still we try on 11th second if not tries on 12th and so on till 15th
|
|
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
|
|
#case DUT will detect client got removed in (10+5) seconds.
|
|
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
|
|
|
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
|
|
#it is period where we send NULL frame.
|
|
#gApLinkMonitorPeriod = 10
|
|
#gGoLinkMonitorPeriod = 10
|
|
|
|
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame
|
|
#are succeed to send or not. Hence total effective detection time is
|
|
# (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) /
|
|
# (gApLinkMonitorPeriod + gApKeepAlivePeriod)
|
|
gGoKeepAlivePeriod = 20
|
|
gApKeepAlivePeriod = 20
|
|
|
|
#If set will start with active scan after driver load, otherwise will start with
|
|
#passive scan to find out the domain
|
|
gEnableBypass11d=1
|
|
|
|
#If set to 0, will not scan DFS channels
|
|
gEnableDFSChnlScan=1
|
|
|
|
# Enable DFS channel roam
|
|
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
|
|
gAllowDFSChannelRoam=2
|
|
|
|
gVhtChannelWidth=2
|
|
|
|
#Data Inactivity Timeout when in powersave (in ms)
|
|
gDataInactivityTimeout=200
|
|
|
|
# Set txchainmask and rxchainmask
|
|
# These parameters are used only if gEnable2x2 is 0
|
|
# Valid values are 1,2
|
|
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
|
|
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
|
|
gSetTxChainmask1x1=1
|
|
gSetRxChainmask1x1=1
|
|
|
|
# Scan Timing Parameters
|
|
# gPassiveMaxChannelTime=110
|
|
# gPassiveMinChannelTime=60
|
|
gActiveMaxChannelTime=40
|
|
gActiveMinChannelTime=20
|
|
|
|
#If set to 0, MCC is not allowed.
|
|
gEnableMCCMode=1
|
|
|
|
# MCC to SCC Switch mode:
|
|
# 0-Disable
|
|
# 1-Enable
|
|
# 2-Force SCC if same band, with SAP restart
|
|
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
|
|
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
|
|
# without SAP restart by sending (E)CSA
|
|
gWlanMccToSccSwitchMode = 0
|
|
|
|
# 1=enable STBC; 0=disable STBC
|
|
gEnableRXSTBC=1
|
|
|
|
# 1=enable tx STBC; 0=disable
|
|
gEnableTXSTBC=1
|
|
|
|
# 1=enable rx LDPC; 0=disable
|
|
gEnableRXLDPC=1
|
|
|
|
#Enable/Disable Tx beamforming
|
|
gTxBFEnable=1
|
|
|
|
#Enable/Disable Tx beamformee in SAP mode
|
|
gEnableTxBFeeSAP=1
|
|
|
|
# Enable Tx beamforming in VHT20MHz
|
|
# Valid values are 0,1. If commented out, the default value is 0.
|
|
# 0=disable, 1=enable
|
|
gEnableTxBFin20MHz=1
|
|
|
|
#Enable/Disable SU Tx beamformer support.
|
|
gEnableTxSUBeamformer=1
|
|
|
|
#Enable thermal mitigation
|
|
gThermalMitigationEnable=0
|
|
|
|
gEnableFastRoamInConcurrency=1
|
|
|
|
#Maxium Channel time in msec
|
|
gMaxMediumTime = 6000
|
|
|
|
# 802.11K support
|
|
gRrmEnable=1
|
|
|
|
# gEnablePowerSaveOffload - Enable Power Save Offload
|
|
#
|
|
# This ini is used to set Power Save Offload configuration:
|
|
# Current values of gEnablePowerSaveOffload:
|
|
# 0 -> Power save offload is disabled
|
|
# 1 -> Legacy Power save enabled + Deep sleep Disabled
|
|
# 2 -> QPower enabled + Deep sleep Disabled
|
|
# 3 -> Legacy Power save enabled + Deep sleep Enabled
|
|
# 4 -> QPower enabled + Deep sleep Enabled
|
|
# 5 -> Duty cycling QPower enabled
|
|
gEnablePowerSaveOffload=2
|
|
|
|
#Enable firmware uart print
|
|
gEnablefwprint=0
|
|
|
|
# Firmware log mode
|
|
# Valid values are 0,1,2
|
|
# 0=Disable, 1=WMI, 2=DIAG
|
|
gEnablefwlog=1
|
|
|
|
# Maximum Receive AMPDU size (VHT only. Valid values:
|
|
# 0->8k 1->16k 2->32k 3->64k 4->128k)
|
|
gVhtAmpduLenExponent=7
|
|
|
|
# Maximum MPDU length (VHT only. Valid values:
|
|
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
|
|
gVhtMpduLen=2
|
|
|
|
# Maximum number of wow filters required
|
|
#gMaxWoWFilters=22
|
|
|
|
# WOW Enable/Disable.
|
|
# 0 - Disable both magic pattern match and pattern byte match.
|
|
# 1 - Enable magic pattern match on all interfaces.
|
|
# 2 - Enable pattern byte match on all interfaces.
|
|
# 3 - Enable both magic pattern and pattern byte match on all interfaces.
|
|
# Default value of gEnableWoW is 3.
|
|
# gEnableWoW=0
|
|
|
|
# Enable or Disable MCC Adaptive Scheduler at the FW
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMCCAdaptiveScheduler=1
|
|
|
|
#Enable or Disable p2p device address administered
|
|
isP2pDeviceAddrAdministrated=0
|
|
|
|
# Set Thermal Power limit
|
|
TxPower2g=10
|
|
TxPower5g=10
|
|
|
|
# Remove Overlap channel restriction
|
|
gEnableOverLapCh=0
|
|
|
|
#Disable VHT on 2.4Ghz
|
|
gEnableVhtFor24GHzBand=0
|
|
|
|
#Maximum number of offload peers supported
|
|
# gMaxOffloadPeers=2
|
|
|
|
# controlling the following offload patterns
|
|
# through ini parameter. Default value is 1
|
|
# to disable set it to zero. ssdp = 0
|
|
# Setup multicast pattern for mDNS 224.0.0.251,
|
|
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
|
|
ssdp=0
|
|
|
|
#Enable Memory Deep Sleep
|
|
gEnableMemDeepSleep=1
|
|
|
|
# Regulatory Setting; 0=STRICT; 1=CUSTOM
|
|
gRegulatoryChangeCountry=1
|
|
|
|
# RA filtering rate limit param, the current value would not
|
|
# help if the lifetime in RA is less than 3*60=3min. Then
|
|
# we need to change it, though it is uncommon.
|
|
# gRAFilterEnable=0
|
|
gRArateLimitInterval=600
|
|
|
|
# Maximum number of concurrent connections
|
|
gMaxConcurrentActiveSessions=3
|
|
|
|
# Disable/Enable GreenAP
|
|
# 0 to disable, 1 to enable, default: 1
|
|
gEnableGreenAp=0
|
|
|
|
# Radar PRI multiplier
|
|
gDFSradarMappingPriMultiplier=4
|
|
|
|
gPNOScanSupport=1
|
|
|
|
#Enable/Disable LPASS support
|
|
# 0 to disable, 1 to enable
|
|
gEnableLpassSupport=1
|
|
|
|
# Whether userspace country code setting shld have priority
|
|
gCountryCodePriority=1
|
|
|
|
# Enable(1)/Disable(0) SIFS burst
|
|
gEnableSifsBurst=1
|
|
|
|
# Enable or Disable Multi-user MIMO
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMuBformee=1
|
|
|
|
# Enable/Disable channel avoidance for SAP in SCC scenario
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gSapSccChanAvoidance=0
|
|
|
|
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
|
|
gIbssTxSpEndInactivityTime=10
|
|
|
|
# Enable support for TDLS
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gEnableTDLSSupport=1
|
|
|
|
# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
|
|
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
|
|
# and RSSI) is met and then will initiate teardown when teardown criteria
|
|
# (idle packet count and RSSI) is met.
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gEnableTDLSImplicitTrigger=1
|
|
|
|
# Enable TDLS External Control. That is, user space application has to
|
|
# first configure a peer MAC in wlan driver towards which TDLS is desired.
|
|
# Device will establish TDLS only towards those configured peers whenever
|
|
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
|
|
# when teardown criteria (idle packet count and RSSI) is met. However,
|
|
# device will accept TDLS connection if it is initiated from any other peer,
|
|
# even if that peer is not configured.
|
|
# 0 - disable
|
|
# 1 - enable
|
|
# For TDLS External Control, Implicit Trigger must also be enabled.
|
|
gTDLSExternalControl=1
|
|
|
|
# Enable support for TDLS off-channel operation
|
|
# 0 - disable
|
|
# 1 - enable
|
|
# TDLS off-channel operation will be invoked when there is only one
|
|
# TDLS connection.
|
|
gEnableTDLSOffChannel=1
|
|
|
|
# Enable or Disable Random MAC (Spoofing)
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMacAddrSpoof=1
|
|
|
|
################ Datapath feature set Begin ################
|
|
# Bus bandwidth threshold values in terms of number of packets
|
|
gBusBandwidthHighThreshold=2000
|
|
gBusBandwidthMediumThreshold=500
|
|
gBusBandwidthLowThreshold=150
|
|
|
|
# Bus bandwidth compute timeout value in ms
|
|
gBusBandwidthComputeInterval=100
|
|
|
|
# VHT Tx/Rx MCS values
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gVhtRxMCS=2
|
|
gVhtTxMCS=2
|
|
|
|
# VHT Tx/Rx MCS values for 2x2
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gEnable2x2=1
|
|
gVhtRxMCS2x2=2
|
|
gVhtTxMCS2x2=2
|
|
|
|
#IPA config is a bit mask and following are the configurations.
|
|
#bit0 IPA Enable
|
|
#bit1 IPA PRE Filter enable
|
|
#bit2 IPv6 enable
|
|
#bit3 IPA Resource Manager (RM) enable
|
|
#bit4 IPA Clock scaling enable
|
|
#bit5 IPA uC ENABLE
|
|
#bit6 IPA uC STA ENABLE
|
|
#bit8 IPA Real Time Debugging
|
|
gIPAConfig=0x7d
|
|
gIPADescSize=800
|
|
|
|
# Enable/Disable RX full reorder offload
|
|
gReorderOffloadSupported=1
|
|
|
|
# Enable CE classification
|
|
# 1 - enable(default) 0 - disable
|
|
gCEClassifyEnable=1
|
|
|
|
# Enable Rx handling options
|
|
# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
|
|
rx_mode=5
|
|
|
|
# Enable(Tx) fastpath for data traffic.
|
|
# 1 - enable(default) 0 - disable
|
|
gEnableFastPath=1
|
|
|
|
# This flag enables IP, TCP and UDP checksum offload
|
|
# 1 - enable(default) 0 - disable
|
|
gEnableIpTcpUdpChecksumOffload=1
|
|
|
|
# Enable TCP Segmentation Offload
|
|
# 1 - enable 0 - disable
|
|
TSOEnable=1
|
|
|
|
# Enable Generic Receive Offload
|
|
# 1 - enable(default) 0 - disable
|
|
GROEnable=1
|
|
|
|
# Enable HT MPDU Density
|
|
# 4 for 2 micro sec
|
|
ght_mpdu_density=4
|
|
|
|
# Enable flow steering to enable multiple CEs for Rx flows.
|
|
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
|
|
# Parallel Rx paths.
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableFlowSteering=1
|
|
|
|
# Time in microseconds after which a NAPI poll must yield
|
|
ce_service_max_yield_time=500
|
|
|
|
#Maximum number of HTT messages to be processed per NAPI poll
|
|
ce_service_max_rx_ind_flush=1
|
|
|
|
# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
|
|
maxMSDUsPerRxInd=8
|
|
|
|
# Enable 802.11k offload
|
|
11k_offload_enable_bitmask=1
|
|
|
|
# Enable NUD tracking feature
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableNUDTracking=1
|
|
|
|
# Enable PEER UNMAP CONF SUPPORT
|
|
# 1 - enable 0 - disable(default)
|
|
gEnablePeerUnmapConfSupport=1
|
|
|
|
################ Datapath feature set End ################
|
|
|
|
################ NAN feature set start ###################
|
|
|
|
# Enable NAN discovery (NAN 1.0)
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableNanSupport=0
|
|
genable_nan_datapath=0
|
|
|
|
################ NAN feature set end #####################
|
|
|
|
# Beacon loss threshold
|
|
gRoamBmissFirstBcnt=10
|
|
gRoamBmissFinalBcnt=10
|
|
|
|
adaptive_dwell_mode_enabled=1
|
|
|
|
hostscan_adaptive_dwell_mode=1
|
|
|
|
adapt_dwell_lpf_weight=80
|
|
|
|
adapt_dwell_wifi_act_threshold=10
|
|
|
|
MAWCEnabled=0
|
|
|
|
drop_bcn_on_chan_mismatch=0
|
|
|
|
# Enable/Disable rtt sta mac randomization
|
|
enable_rtt_mac_randomization=1
|
|
|
|
#Enable/Disable SNR monitoring
|
|
gEnableSNRMonitoring=1
|
|
|
|
# Set IPA low/med/high bandwidth mbps
|
|
gIPALowBandwidthMbps=100
|
|
gIPAMediumBandwidthMbps=400
|
|
gIPAHighBandwidthMbps=800
|
|
|
|
mawc_nlo_enabled=0
|
|
|
|
# [VM1SOM-345][WLAN]: RF Stress Test block in Restarting
|
|
gEnableSelfRecovery=1
|
|
|
|
# P2P feature
|
|
gP2PEnabled=1
|
|
|
|
# Disable packet dump by default
|
|
gEnablePacketStats=0
|
|
|
|
################ Trace Level start ###################
|
|
########### Must add for WifiTracker usage ###########
|
|
qdf_trace_enable_wdi=65535
|
|
qdf_trace_enable_hdd=65535
|
|
qdf_trace_enable_sme=65535
|
|
qdf_trace_enable_pe=65535
|
|
qdf_trace_enable_wma=65535
|
|
qdf_trace_enable_sys=65535
|
|
qdf_trace_enable_qdf=65535
|
|
qdf_trace_enable_sap=65535
|
|
qdf_trace_enable_hdd_sap=65535
|
|
qdf_trace_enable_bmi=65535
|
|
qdf_trace_enable_cfg=65535
|
|
qdf_trace_enable_epping=65535
|
|
qdf_trace_enable_qdf_devices=65535
|
|
cfd_trace_enable_txrx=65535
|
|
qdf_trace_enable_htc=65535
|
|
qdf_trace_enable_hif=65535
|
|
qdf_trace_enable_hdd_sap_data=65535
|
|
qdf_trace_enable_hdd_data=65535
|
|
################ Trace Level end ###################
|
|
|
|
# Trigger the Neighbor Report Request sent 5s delay after the association.
|
|
nr_offload_time_offset=5
|
|
|
|
gNeighborScanChannelList=empty
|
|
|
|
gRoamScanOffloadEnabled=1
|
|
|
|
# Prefer connecting to 5G AP even if its RSSI is lower by gSelect5GHzMargin dBm than 2.4G AP, default 0(range 0~60)
|
|
# This feature requires gRoamPrefer5GHz set to 1 to take effect
|
|
#gSelect5GHzMargin=20
|
|
|
|
#Enable/Disable 5G prefer RSSI boost or penalize, 0(disabled) by default, 1(enabled)
|
|
enable_5g_band_pref=0
|
|
|
|
# Above which 5 GHz is favored, default -76(range -81~-55)
|
|
5g_rssi_boost_threshold=-76
|
|
|
|
# Factor by which 5GHz RSSI is boosted, default 20(range 0~30)
|
|
5g_rssi_boost_factor=20
|
|
|
|
# Maximum boost that can be applied to 5GHz RSSI, default 20(range 0~30)
|
|
5g_max_rssi_boost=20
|
|
|
|
# Below which 5 GHz is not favored, default -80(range -91~-65)
|
|
5g_rssi_penalize_threshold=-80
|
|
|
|
# Disable adaptive dwell mode for scanning
|
|
adaptive_dwell_mode_enabled=0
|
|
|
|
# Disable early stop scan to scan all occupied/full channel
|
|
gEnableEarlyStopScan=0
|
|
|
|
# Disable PMKSA caching to prevent full EAP authentication during roaming after 802.1X session timeout.
|
|
pmkidModes=1
|
|
|
|
# disable scoring logic in FW for candidate selection during roaming
|
|
enable_scoring_for_roam=0
|
|
|
|
# Support to start sap in indoor channel after BSP upgrade to Snapdragon_High_Mid_2017.SPF.3.0, 0.0.031.0
|
|
gindoor_channel_support=1
|
|
|
|
# Roam scan will be rejected if duration between two consecutive requests is less than this time, set to 0
|
|
# to remove this restriction
|
|
min_delay_btw_roam_scans=0
|
|
|
|
|
|
# HiRSSI related
|
|
|
|
# Sets RSSI Delta for scan trigger, default 10(range 0-16)
|
|
# Good region: -30db ~ -60db
|
|
gRoamScanHiRssiDelta=5
|
|
|
|
# set opportunity window as 30min (60 * 30000ms)
|
|
|
|
# Sets 5GHz maximum scan count, default 3(range 0-0x7fffffff)
|
|
# Note that throughput will be affected if value too big
|
|
gRoamScanHiRssiMaxCount=60
|
|
|
|
# Sets minimum delay between 5GHz scans, default 15000(range 5000-0x7fffffff)
|
|
gRoamScanHiRssiDelay=30000
|
|
|
|
# disable dense roaming in dense environment
|
|
groam_dense_rssi_thresh_offset=0
|
|
|
|
# The maximum number of software retries for preauth or reassoc
|
|
roam_preauth_retry_count=10
|
|
# Time to wait (in ms) after sending an preauth or reassoc
|
|
roam_preauth_no_ack_timeout=10
|
|
|
|
# [ASLP-2695]:To enable SAP WLAN RTT feature
|
|
gSapDot11mc=1
|
|
gfine_time_meas_cap=0x8D
|
|
|
|
#Disable adaptive dwell mode for scanning
|
|
#adaptive_dwell_mode_enabled=1
|
|
|
|
hostscan_adaptive_dwell_mode=1
|
|
|
|
adapt_dwell_lpf_weight=80
|
|
|
|
adapt_dwell_wifi_act_threshold=10
|
|
|
|
MAWCEnabled=0
|
|
|
|
drop_bcn_on_chan_mismatch=1
|
|
|
|
# Enable/Disable rtt sta mac randomization
|
|
enable_rtt_mac_randomization=1
|
|
|
|
#Enable/Disable SNR monitoring
|
|
gEnableSNRMonitoring=1
|
|
|
|
# Operating Channel List
|
|
gEnableOperatingChannelList=0
|
|
gOperatingChannelList=
|
|
|
|
# Enable/Disable force bandwidth voting during IPA suspend
|
|
gIPAForceVotingEnable=1
|
|
|
|
mawc_nlo_enabled=0
|
|
|
|
# Prefer roaming to 5GHz Bss
|
|
gRoamPrefer5GHz=1
|
|
|
|
# Prefer connecting to 5G AP even if its RSSI is lower by gSelect5GHzMargin
|
|
# dBm than 2.4G AP
|
|
gSelect5GHzMargin=5
|
|
|
|
#Skip DFS Channel in case of P2P Search
|
|
# 0 - disable (Scan DFS Channel in P2P Search)
|
|
# 1 - enable (Skip DFS Channel)
|
|
gSkipDfsChannelInP2pSearch=0
|
|
|
|
END
|
|
# Note: Configuration parser would not read anything past the END marker
|