51989fce41
When the parameter is set to this value and voice packets are detected in uplink or downlink data traffic, the QPower inactivity timeout is reset to the default QPower-disabled value (200 ms). This means that QPower power saving is not be triggered until after 200ms of inactivity (EAPOL and ARP packets are excluded from the check). Change-Id: I86553a1f1dee73add4eb1b6c3933a39745a16de8 Signed-off-by: pix106 <sbordenave@gmail.com>
654 lines
17 KiB
INI
654 lines
17 KiB
INI
# This file allows user to override the factory
|
|
# defaults for the WLAN Driver
|
|
|
|
# Enable IMPS or not
|
|
gEnableImps=1
|
|
|
|
# Enable BMPS or not
|
|
gEnableBmps=1
|
|
|
|
# Phy Mode (auto, b, g, n, etc)
|
|
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
|
|
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
|
|
# 7 = 11b only 8 = 11ac only.
|
|
gDot11Mode=0
|
|
|
|
# Assigned MAC Addresses - This will be used until NV items are in place
|
|
# Each byte of MAC address is represented in Hex format as XX
|
|
Intf0MacAddress=000AF58989FF
|
|
Intf1MacAddress=000AF58989FE
|
|
Intf2MacAddress=000AF58989FD
|
|
Intf3MacAddress=000AF58989FC
|
|
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
|
InfraUapsdVoSrvIntv=0
|
|
InfraUapsdViSrvIntv=0
|
|
InfraUapsdBeSrvIntv=0
|
|
InfraUapsdBkSrvIntv=0
|
|
|
|
# Flag to allow STA send AddTspec even when ACM is Off
|
|
gAddTSWhenACMIsOff=1
|
|
|
|
# Flags to filter Mcast and Bcast RX packets.
|
|
# Value 0: No filtering, 1: Filter all Multicast.
|
|
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
|
|
McastBcastFilter=3
|
|
|
|
#Flag to enable HostARPOffload feature or not
|
|
hostArpOffload=1
|
|
|
|
#Flag to enable HostNSOffload feature or not
|
|
hostNSOffload=1
|
|
|
|
# 802.11n Protection flag
|
|
gEnableApProt=1
|
|
|
|
#Enable OBSS protection
|
|
gEnableApOBSSProt=1
|
|
|
|
#Enable/Disable UAPSD for SoftAP
|
|
gEnableApUapsd=1
|
|
|
|
# Fixed Rate
|
|
gFixedRate=0
|
|
|
|
# Maximum Tx power
|
|
# gTxPowerCap=30
|
|
|
|
# Fragmentation Threshold
|
|
# gFragmentationThreshold=2346
|
|
|
|
# RTS threshold
|
|
RTSThreshold=1048576
|
|
|
|
# Intra-BSS forward
|
|
gDisableIntraBssFwd=0
|
|
|
|
# WMM Enable/Disable
|
|
WmmIsEnabled=0
|
|
|
|
# 802.11d support
|
|
g11dSupportEnabled=0
|
|
|
|
# 802.11h support
|
|
g11hSupportEnabled=1
|
|
|
|
# DFS Master Capability
|
|
gEnableDFSMasterCap=1
|
|
|
|
# ESE Support and fast transition
|
|
EseEnabled=0
|
|
|
|
ImplicitQosIsEnabled=0
|
|
|
|
gNeighborScanTimerPeriod=200
|
|
gNeighborLookupThreshold=85
|
|
gNeighborScanChannelMinTime=20
|
|
gNeighborScanChannelMaxTime=30
|
|
gMaxNeighborReqTries=3
|
|
|
|
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
|
# To enable, set FastRoamEnabled=1
|
|
# To disable, set FastRoamEnabled=0
|
|
FastRoamEnabled=1
|
|
|
|
# Check if the AP to which we are roaming is better than current AP in
|
|
# terms of RSSI. Checking is disabled if set to Zero.Otherwise it will
|
|
# use this value as to how better the RSSI of the new/roamable AP should
|
|
# be for roaming
|
|
RoamRssiDiff=5
|
|
|
|
# To enable, set gRoamIntraBand=1 (Roaming within band)
|
|
# To disable, set gRoamIntraBand=0 (Roaming across band)
|
|
gRoamIntraBand=0
|
|
# Sets RSSI preference for 5GHz over 2.4GHz AP
|
|
gSelect5GHzMargin=5
|
|
|
|
# RSSI threshold offset for 2G to 5G roam
|
|
roam_bad_rssi_thresh_offset_2g=0
|
|
|
|
#RSSI threshold for background roam
|
|
roam_bg_scan_bad_rssi_thresh=-76
|
|
|
|
#Short Guard Interval Enable/disable
|
|
gShortGI20Mhz=1
|
|
gShortGI40Mhz=1
|
|
|
|
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
|
|
gAPAutoShutOff=0
|
|
|
|
#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
|
|
gWlanAutoShutdown = 0
|
|
|
|
# Not used.
|
|
gApAutoChannelSelection=0
|
|
|
|
#Preferred band (both or 2.4 only or 5 only)
|
|
BandCapability=0
|
|
|
|
#Channel Bonding
|
|
gChannelBondingMode5GHz=1
|
|
gChannelBondingMode24GHz=1
|
|
|
|
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
|
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
|
|
#is idle for last 10 seconds.) For both active and power save clients.
|
|
|
|
#Power save clients: DUT set TIM bit from 10th second onwards and till client
|
|
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
|
|
|
|
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
|
|
#success still we try on 11th second if not tries on 12th and so on till 15th
|
|
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
|
|
#case DUT will detect client got removed in (10+5) seconds.
|
|
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
|
|
|
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
|
|
#it is period where we send NULL frame.
|
|
#gApLinkMonitorPeriod = 10
|
|
#gGoLinkMonitorPeriod = 10
|
|
|
|
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame
|
|
#are succeed to send or not. Hence total effective detection time is
|
|
# (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) /
|
|
# (gApLinkMonitorPeriod + gApKeepAlivePeriod)
|
|
gGoKeepAlivePeriod = 20
|
|
gApKeepAlivePeriod = 20
|
|
|
|
#Enable Keep alive with non-zero period value
|
|
gStaKeepAlivePeriod = 30
|
|
|
|
#If set will start with active scan after driver load, otherwise will start with
|
|
#passive scan to find out the domain
|
|
gEnableBypass11d=1
|
|
|
|
#If set to 0, will not scan DFS channels
|
|
gEnableDFSChnlScan=1
|
|
|
|
# Enable DFS channel roam
|
|
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
|
|
gAllowDFSChannelRoam=1
|
|
|
|
gVhtChannelWidth=2
|
|
|
|
#Data Inactivity Timeout when in powersave (in ms)
|
|
gDataInactivityTimeout=200
|
|
|
|
# Set txchainmask and rxchainmask
|
|
# These parameters are used only if gEnable2x2 is 0
|
|
# Valid values are 1,2
|
|
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
|
|
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
|
|
gSetTxChainmask1x1=1
|
|
gSetRxChainmask1x1=1
|
|
|
|
# Scan Timing Parameters
|
|
# gPassiveMaxChannelTime=110
|
|
# gPassiveMinChannelTime=60
|
|
gActiveMaxChannelTime=40
|
|
gActiveMinChannelTime=20
|
|
|
|
#If set to 0, MCC is not allowed.
|
|
gEnableMCCMode=1
|
|
|
|
# MCC to SCC Switch mode:
|
|
# 0-Disable
|
|
# 1-Enable
|
|
# 2-Force SCC if same band, with SAP restart
|
|
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
|
|
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
|
|
# without SAP restart by sending (E)CSA
|
|
gWlanMccToSccSwitchMode = 3
|
|
|
|
# 1=enable STBC; 0=disable STBC
|
|
gEnableRXSTBC=1
|
|
|
|
# 1=enable tx STBC; 0=disable
|
|
gEnableTXSTBC=1
|
|
|
|
# 1=enable rx LDPC; 0=disable
|
|
gEnableRXLDPC=1
|
|
|
|
#Enable/Disable Tx beamforming
|
|
gTxBFEnable=1
|
|
|
|
#Enable/Disable Tx beamformee in SAP mode
|
|
gEnableTxBFeeSAP=1
|
|
|
|
# Enable Tx beamforming in VHT20MHz
|
|
# Valid values are 0,1. If commented out, the default value is 0.
|
|
# 0=disable, 1=enable
|
|
gEnableTxBFin20MHz=1
|
|
|
|
#Enable/Disable SU Tx beamformer support.
|
|
gEnableTxSUBeamformer=1
|
|
|
|
gEnableFastRoamInConcurrency=1
|
|
|
|
#Maxium Channel time in msec
|
|
gMaxMediumTime = 6000
|
|
|
|
# 802.11K support
|
|
gRrmEnable=1
|
|
|
|
#Enable Power Save offload
|
|
gEnablePowerSaveOffload=5
|
|
|
|
#Enable firmware uart print
|
|
gEnablefwprint=0
|
|
|
|
# Firmware log mode
|
|
# Valid values are 0,1,2
|
|
# 0=Disable, 1=WMI, 2=DIAG
|
|
gEnablefwlog=0
|
|
|
|
# Maximum Receive AMPDU size (VHT only. Valid values:
|
|
# 0->8k 1->16k 2->32k 3->64k 4->128k)
|
|
gVhtAmpduLenExponent=7
|
|
|
|
# Maximum MPDU length (VHT only. Valid values:
|
|
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
|
|
gVhtMpduLen=2
|
|
|
|
# Maximum number of wow filters required
|
|
#gMaxWoWFilters=22
|
|
|
|
# WOW Enable/Disable.
|
|
# 0 - Disable both magic pattern match and pattern byte match.
|
|
# 1 - Enable magic pattern match on all interfaces.
|
|
# 2 - Enable pattern byte match on all interfaces.
|
|
# 3 - Enable both magic pattern and pattern byte match on all interfaces.
|
|
# Default value of gEnableWoW is 3.
|
|
# gEnableWoW=0
|
|
|
|
# Enable or Disable MCC Adaptive Scheduler at the FW
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMCCAdaptiveScheduler=1
|
|
|
|
#Skip DFS Channel in case of P2P Search
|
|
# 0 - disable (Scan DFS Channel in P2P Search)
|
|
# 1 - enable (Skip DFS Channel)
|
|
gSkipDfsChannelInP2pSearch=0
|
|
|
|
#Enable or Disable p2p device address administered
|
|
isP2pDeviceAddrAdministrated=0
|
|
|
|
# Remove Overlap channel restriction
|
|
gEnableOverLapCh=0
|
|
|
|
#Enable VHT on 2.4Ghz
|
|
gEnableVhtFor24GHzBand=1
|
|
|
|
#Maximum number of offload peers supported
|
|
# gMaxOffloadPeers=2
|
|
|
|
# controlling the following offload patterns
|
|
# through ini parameter. Default value is 1
|
|
# to disable set it to zero. ssdp = 0
|
|
# Setup multicast pattern for mDNS 224.0.0.251,
|
|
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
|
|
ssdp=0
|
|
|
|
#Enable Memory Deep Sleep
|
|
gEnableMemDeepSleep=1
|
|
|
|
# Regulatory Setting; 0=STRICT; 1=CUSTOM
|
|
gRegulatoryChangeCountry=1
|
|
|
|
# RA filtering rate limit param, the current value would not
|
|
# help if the lifetime in RA is less than 3*60=3min. Then
|
|
# we need to change it, though it is uncommon.
|
|
# gRAFilterEnable=0
|
|
gRArateLimitInterval=600
|
|
|
|
# Maximum number of concurrent connections
|
|
gMaxConcurrentActiveSessions=3
|
|
|
|
# Disable/Enable GreenAP
|
|
# 0 to disable, 1 to enable, default: 1
|
|
gEnableGreenAp=1
|
|
|
|
# Disable/Enbale Enhanced Green AP
|
|
# 0 to disable, 1 to enable, default: 0
|
|
gEnableEGAP=1
|
|
|
|
# Radar PRI multiplier
|
|
gDFSradarMappingPriMultiplier=4
|
|
|
|
gPNOScanSupport=1
|
|
|
|
#Enable/Disable LPASS support
|
|
# 0 to disable, 1 to enable
|
|
gEnableLpassSupport=1
|
|
|
|
# Whether userspace country code setting shld have priority
|
|
gCountryCodePriority=1
|
|
|
|
# Enable(1)/Disable(0) SIFS burst
|
|
gEnableSifsBurst=1
|
|
|
|
# Enable or Disable Multi-user MIMO
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMuBformee=1
|
|
|
|
# Enable/Disable channel avoidance for SAP in SCC scenario
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gSapSccChanAvoidance=0
|
|
|
|
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
|
|
gIbssTxSpEndInactivityTime=10
|
|
|
|
# Enable support for TDLS
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gEnableTDLSSupport=1
|
|
|
|
# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
|
|
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
|
|
# and RSSI) is met and then will initiate teardown when teardown criteria
|
|
# (idle packet count and RSSI) is met.
|
|
# 0 - disable
|
|
# 1 - enable
|
|
gEnableTDLSImplicitTrigger=1
|
|
|
|
# Enable TDLS External Control. That is, user space application has to
|
|
# first configure a peer MAC in wlan driver towards which TDLS is desired.
|
|
# Device will establish TDLS only towards those configured peers whenever
|
|
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
|
|
# when teardown criteria (idle packet count and RSSI) is met. However,
|
|
# device will accept TDLS connection if it is initiated from any other peer,
|
|
# even if that peer is not configured.
|
|
# 0 - disable
|
|
# 1 - enable
|
|
# For TDLS External Control, Implicit Trigger must also be enabled.
|
|
gTDLSExternalControl=1
|
|
|
|
# Enable support for TDLS off-channel operation
|
|
# 0 - disable
|
|
# 1 - enable
|
|
# TDLS off-channel operation will be invoked when there is only one
|
|
# TDLS connection.
|
|
gEnableTDLSOffChannel=0
|
|
|
|
# Enable or Disable Random MAC (Spoofing)
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMacAddrSpoof=1
|
|
|
|
################ Datapath feature set Begin ################
|
|
# Bus bandwidth threshold values in terms of number of packets
|
|
gBusBandwidthHighThreshold=2000
|
|
gBusBandwidthMediumThreshold=500
|
|
gBusBandwidthLowThreshold=150
|
|
|
|
# Bus bandwidth compute timeout value in ms
|
|
gBusBandwidthComputeInterval=100
|
|
|
|
# VHT Tx/Rx MCS values
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gVhtRxMCS=2
|
|
gVhtTxMCS=2
|
|
|
|
# VHT Tx/Rx MCS values for 2x2
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gEnable2x2=1
|
|
gVhtRxMCS2x2=2
|
|
gVhtTxMCS2x2=2
|
|
|
|
#IPA config is a bit mask and following are the configurations.
|
|
#bit0 IPA Enable
|
|
#bit1 IPA PRE Filter enable
|
|
#bit2 IPv6 enable
|
|
#bit3 IPA Resource Manager (RM) enable
|
|
#bit4 IPA Clock scaling enable
|
|
#bit5 IPA uC ENABLE
|
|
#bit6 IPA uC STA ENABLE
|
|
#bit8 IPA Real Time Debugging
|
|
gIPAConfig=0x7d
|
|
gIPADescSize=800
|
|
|
|
# Enable/Disable RX full reorder offload
|
|
gReorderOffloadSupported=1
|
|
|
|
# Enable CE classification
|
|
# 1 - enable(default) 0 - disable
|
|
gCEClassifyEnable=1
|
|
|
|
# Enable Rx handling options
|
|
# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
|
|
rx_mode=5
|
|
|
|
# Enable(Tx) fastpath for data traffic.
|
|
# 1 - enable(default) 0 - disable
|
|
gEnableFastPath=1
|
|
|
|
# This flag enables IP, TCP and UDP checksum offload
|
|
# 1 - enable(default) 0 - disable
|
|
gEnableIpTcpUdpChecksumOffload=1
|
|
|
|
# Enable TCP Segmentation Offload
|
|
# 1 - enable 0 - disable
|
|
TSOEnable=1
|
|
|
|
# Enable Generic Receive Offload
|
|
# 1 - enable(default) 0 - disable
|
|
GROEnable=1
|
|
|
|
# Enable HT MPDU Density
|
|
# 4 for 2 micro sec
|
|
ght_mpdu_density=4
|
|
|
|
# Enable flow steering to enable multiple CEs for Rx flows.
|
|
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
|
|
# Parallel Rx paths.
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableFlowSteering=1
|
|
|
|
#set get linklayer status support
|
|
gEnableLLStats=1
|
|
|
|
# Time in microseconds after which a NAPI poll must yield
|
|
ce_service_max_yield_time=500
|
|
|
|
#Maximum number of HTT messages to be processed per NAPI poll
|
|
ce_service_max_rx_ind_flush=1
|
|
|
|
# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
|
|
maxMSDUsPerRxInd=8
|
|
|
|
# Enable NUD tracking feature
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableNUDTracking=1
|
|
|
|
# Enable PEER UNMAP CONF SUPPORT
|
|
# 1 - enable 0 - disable(default)
|
|
gEnablePeerUnmapConfSupport=1
|
|
|
|
################ Datapath feature set End ################
|
|
|
|
################ NAN feature set start ###################
|
|
|
|
# Enable NAN discovery (NAN 1.0)
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableNanSupport=1
|
|
# Enable NAN Datapath
|
|
genable_nan_datapath=1
|
|
|
|
################ NAN feature set end #####################
|
|
|
|
adaptive_dwell_mode_enabled=1
|
|
|
|
hostscan_adaptive_dwell_mode=1
|
|
|
|
adapt_dwell_lpf_weight=80
|
|
|
|
adapt_dwell_wifi_act_threshold=10
|
|
|
|
# Enable pkt log
|
|
# 1 - enable, 0 - disable
|
|
gEnablePacketLog=1
|
|
|
|
# Force 1x1 for 2.4g SAP, P2P-GC/GO, 2x2 for STA
|
|
# gVdevTypeNss_2g=21846
|
|
|
|
# 0: Disable BPF packet filter
|
|
# 1: Enable BPF packet filter
|
|
gBpfFilterEnable=1
|
|
|
|
# 0: Disable force 1x1 on MTK solution AP
|
|
# 1: Enable force 1x1 on MTK solution AP
|
|
# gForce1x1Exception=1
|
|
|
|
# set modulated DTIM interval
|
|
gEnableModulatedDTIM=3
|
|
gMaxLIModulatedDTIM=3
|
|
|
|
# groam_dense_rssi_thresh_offset - Sets dense roam RSSI threshold diff
|
|
groam_dense_rssi_thresh_offset=5
|
|
|
|
# Dense traffic threshold in kBps
|
|
gtraffic_threshold=50
|
|
|
|
# Set beacon missed count threshold
|
|
# if beacon missed counter > gRoamBmissFirstBcnt+gRoamBmissFinalBcnt,
|
|
# heartbeat error triggered
|
|
gRoamBmissFirstBcnt=10
|
|
gRoamBmissFinalBcnt=20
|
|
|
|
# To enabled/disable PER based roaming in FW
|
|
# 0: disabled
|
|
# 1: enabled for Rx traffic
|
|
# 2: enabled for Tx traffic
|
|
# 3: enabled for Tx and Rx traffic
|
|
gper_roam_enabled=0
|
|
|
|
# arp_ac_category - ARP access category
|
|
# Firmware by default categorizes ARP packets with VOICE TID.
|
|
# WME_AC_BE = 0 (Best effort)
|
|
# WME_AC_BK = 1 (Background)
|
|
# WME_AC_VI = 2 (Video)
|
|
# WME_AC_VO = 3 (Voice)
|
|
arp_ac_category=0
|
|
# Enable/Disable DTIM Synth
|
|
# 1- Enable DTIM Synth
|
|
# 0- Disable DTIM Synth
|
|
gEnableLPRx=0
|
|
|
|
enable_scoring_for_roam=1
|
|
|
|
oce_enable_probe_req_deferral=1
|
|
|
|
oce_enable_probe_req_rate=1
|
|
|
|
enable_esp_for_roam=1
|
|
##################### Scoring Param ###############
|
|
esp_qbss_score_idx7_to_4=0000000A
|
|
|
|
#############################################
|
|
# MAWC related configurations
|
|
#############################################
|
|
|
|
# MAWCEnabled - Enable/Disable Motion Aided Wireless Connectivity Global
|
|
MAWCEnabled=0
|
|
|
|
# mawc_roam_enabled - Enable/Disable MAWC during roaming
|
|
mawc_roam_enabled=0
|
|
|
|
# Enable/Disable the Motion Aided Wireless Connectivity
|
|
# based NLO using this parameter
|
|
mawc_nlo_enabled=0
|
|
|
|
# Enable Packet filters before going into suspend
|
|
# will clear those when resume
|
|
# bit-0 : drop MAC multicast and IPv4 multicast
|
|
# bit-1 : drop MAC unicast and IPv4 multicast
|
|
# bit-2 : drop IPv4 broadcast
|
|
# bit-3 : drop XID - Exchange station Identification packet
|
|
# bit-4 : drop STP - Spanning Tree Protocol
|
|
# bit-5 : drop DTP/LLC/CDP
|
|
g_enable_packet_filter_bitmap=3
|
|
|
|
# Enable/Disable Data stall detection
|
|
# 0: disable
|
|
# 1: enable
|
|
gEnableDataStallDetection=0
|
|
|
|
#Enable host side recovery
|
|
gEnableSelfRecovery=1
|
|
|
|
#enable/disable FT open feature
|
|
enable_ftopen=0
|
|
|
|
# This ini is used to allow STA+SAP SCC on LTE coex channel
|
|
# 0 - Disallow STA+SAP SCC on LTE coex channel
|
|
# 1 - Allow STA+SAP SCC on LTE coex channel
|
|
g_sta_sap_scc_on_lte_coex_chan=1
|
|
|
|
#Add another interface while driver load
|
|
gEnableConcurrentSTA=wlan1
|
|
|
|
# This ini is used to allow STA+SAP SCC on DFS channel with master mode
|
|
# support disabled
|
|
# 0 - Disallow STA+SAP SCC on DFS channel
|
|
# 1 - Allow STA+SAP SCC on DFS channel with master mode disabled
|
|
g_sta_sap_scc_on_dfs_chan=1
|
|
|
|
# Disable RX wakelock feature
|
|
rx_wakelock_timeout=0
|
|
|
|
# Enable Target Wake Time support
|
|
enable_twt=0
|
|
|
|
# This ini is used to set early stop scan. Early stop
|
|
# scan is a feature for roaming to stop the scans at
|
|
# an early stage as soon as we find a better AP to roam.
|
|
# This would make the roaming happen quickly.
|
|
gEnableEarlyStopScan=1
|
|
|
|
# This ini is used to increase/decrease PCL weightage in best
|
|
# candidate selection.
|
|
# If some APs are in PCL list, those AP will get addition weightage.
|
|
pcl_weightage=0
|
|
|
|
# Currently Firmware update the sequence number for each TID with
|
|
# because of security issues. But with this PN mechanism, throughput drop
|
|
# is observed. With this ini FW takes the decision to trade off between
|
|
# security and throughput
|
|
gcmp_enabled=0
|
|
|
|
gTxBFCsnValue=4
|
|
|
|
# etsi13_srd_chan_in_master_mode - Enable/disable ETSI SRD channels in
|
|
# etsi_srd_chan_in_master_mode - Enable/disable ETSI SRD channels in
|
|
# master mode PCL and ACS functionality
|
|
# @Min: 0
|
|
# @Max: 1
|
|
# @Default: 0
|
|
etsi13_srd_chan_in_master_mode=1
|
|
etsi_srd_chan_in_master_mode=1
|
|
|
|
gActiveUcBpfMode=1
|
|
gActiveMcBcBpfMode=1
|
|
|
|
drop_bcn_on_chan_mismatch=0
|
|
|
|
# Enable/Disable rtt sta mac randomization
|
|
enable_rtt_mac_randomization=1
|
|
|
|
#Enable/Disable SNR monitoring
|
|
gEnableSNRMonitoring=1
|
|
|
|
#Skip DFS Channel in case of P2P Search
|
|
# 0 - disable (Scan DFS Channel in P2P Search)
|
|
# 1 - enable (Skip DFS Channel)
|
|
gSkipDfsChannelInP2pSearch=0
|
|
|
|
# TheCrazyLex@PA Prefer connecting to 5Ghz AP
|
|
# even if its RSSI is lower by 5dBm than the 2.4Ghz AP.
|
|
gRoamPrefer5GHz=1
|
|
gSelect5GHzMargin=5
|
|
END
|
|
|
|
# Note: Configuration parser would not read anything past the END marker
|