diff --git a/gps/etc/gnss_antenna_info.conf b/gps/etc/gnss_antenna_info.conf
index 79a2aefb..e037daa5 100644
--- a/gps/etc/gnss_antenna_info.conf
+++ b/gps/etc/gnss_antenna_info.conf
@@ -80,7 +80,8 @@
 # NUMBER_OF_ROWS_SGC_ and NUMBER_OF_COLUMNS_SGC_ represent the number of
 # rows/columns for signal gain corrections
 
-ANTENNA_INFO_VECTOR_SIZE = 2
+# ANTENNA_INFO_VECTOR_SIZE must be non zero if antenna corrections are sent
+# ANTENNA_INFO_VECTOR_SIZE = 2
 
 CARRIER_FREQUENCY_0 = 1575.42
 
diff --git a/gps/etc/gps.conf b/gps/etc/gps.conf
index bc6b40e1..75f12f2f 100644
--- a/gps/etc/gps.conf
+++ b/gps/etc/gps.conf
@@ -18,7 +18,7 @@ DEBUG_LEVEL = 3
 INTERMEDIATE_POS=0
 
 # supl version 1.0
-SUPL_VER=0x20000
+SUPL_VER=0x10000
 
 # Emergency SUPL, 1=enable, 0=disable
 #SUPL_ES=1
@@ -26,7 +26,7 @@ SUPL_VER=0x20000
 #Choose PDN for Emergency SUPL
 #1 - Use emergency PDN
 #0 - Use regular SUPL PDN for Emergency SUPL
-USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=1
+#USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0
 
 #SUPL_MODE is a bit mask set in config.xml per carrier by default.
 #If it is uncommented here, this value will overwrite the value from
@@ -41,7 +41,7 @@ USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=1
 # MSA = 0x04
 # ON_DEMAND_TIME = 0x10
 # default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING
-CAPABILITIES=0x37
+CAPABILITIES=0x17
 
 # Accuracy threshold for intermediate positions
 # less accurate positions are ignored, 0 for passing all positions
@@ -54,8 +54,6 @@ CAPABILITIES=0x37
 # FOR SUPL SUPPORT, set the following
 # SUPL_HOST=supl.host.com or IP
 # SUPL_PORT=1234
-SUPL_HOST=supl.google.com
-SUPL_PORT=7276
 
 # FOR MO SUPL SUPPORT, set the following
 # MO_SUPL_HOST=supl.host.com or IP
@@ -148,7 +146,7 @@ SGLTE_TARGET=0
 # 0x1: RRC CPlane
 # 0x2: RRLP UPlane
 # 0x4: LLP Uplane
-A_GLONASS_POS_PROTOCOL_SELECT = 15
+A_GLONASS_POS_PROTOCOL_SELECT = 0
 
 ##################################################
 # Select technology for LPPe Control Plane
@@ -157,7 +155,7 @@ A_GLONASS_POS_PROTOCOL_SELECT = 15
 # 0x2: WLAN AP Measurements for LPPe CP
 # 0x4: SRN AP measurement for CP
 # 0x8: Sensor Barometer Measurement LPPe CP
-LPPE_CP_TECHNOLOGY = 0
+#LPPE_CP_TECHNOLOGY = 0
 
 ##################################################
 # Select technology for LPPe User Plane
@@ -166,7 +164,7 @@ LPPE_CP_TECHNOLOGY = 0
 # 0x2: WLAN AP Measurements for LPPe UP
 # 0x4: SRN AP measurement for UP
 # 0x8: Sensor Barometer Measurement LPPe UP
-LPPE_UP_TECHNOLOGY = 0
+#LPPE_UP_TECHNOLOGY = 0
 
 ##################################################
 # AGPS_CONFIG_INJECT