android_device_xiaomi_sdm660-common/configs/wifi/WCNSS_qcom_cfg.ini

# This file allows user to override the factory
# defaults for the WLAN Driver

# gVersion needs to be increased once the parameters in this file is changed
# in order to update the ini file from /vendor/etc/wifi/ into /data/misc/wifi folder.
gVersion=12.0.1

# Enable IMPS or not
gEnableImps=1

# Enable BMPS or not
gEnableBmps=1

# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
# 7 = 11b only 8 = 11ac only.
gDot11Mode=0

# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC

# UAPSD service interval for VO,VI, BE, BK traffic
InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0

# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1

# Flags to filter Mcast and Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=3

#Flag to enable HostARPOffload feature or not
hostArpOffload=1

#Flag to enable HostNSOffload feature or not
hostNSOffload=1

# 802.11n Protection flag
gEnableApProt=1

#Enable OBSS protection
gEnableApOBSSProt=1

#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1

# Fixed Rate
gFixedRate=0

# Maximum Tx power
# gTxPowerCap=30

# Fragmentation Threshold
# gFragmentationThreshold=2346

# RTS threshold
RTSThreshold=1048576

# Intra-BSS forward
gDisableIntraBssFwd=0

# WMM Enable/Disable
WmmIsEnabled=0

# 802.11d support
g11dSupportEnabled=1

# 11d host offload
ignore_fw_reg_offload_ind=1

# 802.11h support
g11hSupportEnabled=1

# DFS Master Capability
gEnableDFSMasterCap=1

# ESE Support and fast transition
EseEnabled=1

ImplicitQosIsEnabled=0

# If AP signal is changing quickly (like in warehouse), cannot wait 200 seconds to trigger scan
gNeighborScanTimerPeriod=200
gRoamRestTimeMin=50
#200 to 5 for roaming scan
gNeighborLookupThreshold=85
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
gMaxNeighborReqTries=3

# Roaming requirement states that we must perform roam scan by default every 5 seconds while RSSI is low
#gNeighborScanRefreshPeriod=5000

# If no candidate is found, perform another scan after 5 seconds
# Rapid scanning will drain battery and doesn't make sense since AP conditions don't change that quickly
# Also, '0' might mean that if no candidate is found, then scan is not refreshed at all
gEmptyScanRefreshPeriod=5000

# Legacy (non-ESE, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1

# Check if the AP to which we are roaming is better than current AP in
# terms of RSSI.  Checking is disabled if set to Zero.Otherwise it will
# use this value as to how better the RSSI of the new/roamable AP should
# be for roaming
RoamRssiDiff=5

# To enable, set gRoamIntraBand=1 (Roaming within band)
# To disable, set gRoamIntraBand=0 (Roaming across band)
gRoamIntraBand=0

#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1

#Auto Shutdown  Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0

#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
gWlanAutoShutdown = 0

# Not used.
gApAutoChannelSelection=0

#Preferred band (both or 2.4 only or 5 only)
BandCapability=0

#Channel Bonding
gChannelBondingMode5GHz=1
gChannelBondingMode24GHz=1

#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
#is idle for last 10 seconds.) For both active and power save clients.

#Power save clients: DUT set TIM bit from 10th second onwards and till client
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.

#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
#success still we try on 11th second if not tries on 12th and so on till 15th
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
#case DUT will detect client got removed in (10+5) seconds.
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..

#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
#it is period where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10

#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame
#are succeed to send or not. Hence total effective detection time is
# (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) /
# (gApLinkMonitorPeriod + gApKeepAlivePeriod)
gGoKeepAlivePeriod = 20
gApKeepAlivePeriod = 20

#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
gEnableBypass11d=1

#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1

# Enable DFS channel roam
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
gAllowDFSChannelRoam=2

gVhtChannelWidth=2

#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=200

# Set txchainmask and rxchainmask
# These parameters are used only if gEnable2x2 is 0
# Valid values are 1,2
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
gSetTxChainmask1x1=1
gSetRxChainmask1x1=1

# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
gActiveMaxChannelTime=40
gActiveMinChannelTime=20

#If set to 0, MCC is not allowed.
gEnableMCCMode=1

# MCC to SCC Switch mode:
# 0-Disable
# 1-Enable
# 2-Force SCC if same band, with SAP restart
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
#   without SAP restart by sending (E)CSA
gWlanMccToSccSwitchMode = 0

# 1=enable STBC; 0=disable STBC
gEnableRXSTBC=1

# 1=enable tx STBC; 0=disable
gEnableTXSTBC=1

# 1=enable rx LDPC; 0=disable
gEnableRXLDPC=1

#Enable/Disable Tx beamforming
gTxBFEnable=1

#Enable/Disable Tx beamformee in SAP mode
gEnableTxBFeeSAP=1

# Enable Tx beamforming in VHT20MHz
# Valid values are 0,1. If commented out, the default value is 0.
# 0=disable, 1=enable
gEnableTxBFin20MHz=1

#Enable/Disable SU Tx beamformer support.
gEnableTxSUBeamformer=1

#Enable thermal mitigation
gThermalMitigationEnable=0

gEnableFastRoamInConcurrency=1

#Maxium Channel time in msec
gMaxMediumTime = 6000

# 802.11K support
gRrmEnable=1

# gEnablePowerSaveOffload - Enable Power Save Offload
#
# This ini is used to set Power Save Offload configuration:
# Current values of gEnablePowerSaveOffload:
# 0 -> Power save offload is disabled
# 1 -> Legacy Power save enabled + Deep sleep Disabled
# 2 -> QPower enabled + Deep sleep Disabled
# 3 -> Legacy Power save enabled + Deep sleep Enabled
# 4 -> QPower enabled + Deep sleep Enabled
# 5 -> Duty cycling QPower enabled
gEnablePowerSaveOffload=2

#Enable firmware uart print
gEnablefwprint=0

# Firmware log mode
# Valid values are 0,1,2
# 0=Disable, 1=WMI, 2=DIAG
gEnablefwlog=0

# Maximum Receive AMPDU size (VHT only. Valid values:
# 0->8k 1->16k 2->32k 3->64k 4->128k)
gVhtAmpduLenExponent=7

# Maximum MPDU length (VHT only. Valid values:
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
gVhtMpduLen=2

# Maximum number of wow filters required
#gMaxWoWFilters=22

# WOW Enable/Disable.
# 0 - Disable both magic pattern match and pattern byte match.
# 1 - Enable magic pattern match on all interfaces.
# 2 - Enable pattern byte match on all interfaces.
# 3 - Enable both magic pattern and pattern byte match on all interfaces.
# Default value of gEnableWoW is 3.
# gEnableWoW=0

# Enable or Disable MCC Adaptive Scheduler at the FW
# 1=Enable (default), 0=Disable
gEnableMCCAdaptiveScheduler=1

#Enable or Disable p2p device address administered
isP2pDeviceAddrAdministrated=0

# Set Thermal Power limit
TxPower2g=10
TxPower5g=10

# Remove Overlap channel restriction
gEnableOverLapCh=0

#Disable VHT on 2.4Ghz
gEnableVhtFor24GHzBand=0

#Maximum number of offload peers supported
# gMaxOffloadPeers=2

# controlling the following offload patterns
# through ini parameter. Default value is 1
# to disable set it to zero. ssdp = 0
# Setup multicast pattern for mDNS 224.0.0.251,
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
ssdp=0

#Enable Memory Deep Sleep
gEnableMemDeepSleep=1

# Regulatory Setting; 0=STRICT; 1=CUSTOM
gRegulatoryChangeCountry=1

# RA filtering rate limit param, the current value would not
# help if the lifetime in RA is less than 3*60=3min. Then
# we need to change it, though it is uncommon.
# gRAFilterEnable=0
gRArateLimitInterval=600

# Maximum number of concurrent connections
gMaxConcurrentActiveSessions=3

# Disable/Enable GreenAP
# 0 to disable, 1 to enable, default: 1
gEnableGreenAp=0

# Radar PRI multiplier
gDFSradarMappingPriMultiplier=4

gPNOScanSupport=1

#Enable/Disable LPASS support
# 0 to disable, 1 to enable
gEnableLpassSupport=1

# Whether userspace country code setting shld have priority
gCountryCodePriority=1

# Enable(1)/Disable(0) SIFS burst
gEnableSifsBurst=1

# Enable or Disable Multi-user MIMO
# 1=Enable (default), 0=Disable
gEnableMuBformee=1

# Enable/Disable channel avoidance for SAP in SCC scenario
# 0 - disable
# 1 - enable
gSapSccChanAvoidance=0

# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
gIbssTxSpEndInactivityTime=10

# Enable support for TDLS
#  0 - disable
#  1 - enable
gEnableTDLSSupport=1

# Enable support for Implicit Trigger of TDLS. That is, wlan driver shall
# initiate TDLS Discovery towards a peer whenever setup criteria (throughput
# and RSSI) is met and then will initiate teardown when teardown criteria
# (idle packet count and RSSI) is met.
#  0 - disable
#  1 - enable
gEnableTDLSImplicitTrigger=1

# Enable TDLS External Control. That is, user space application has to
# first configure a peer MAC in wlan driver towards which TDLS is desired.
# Device will establish TDLS only towards those configured peers whenever
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
# when teardown criteria (idle packet count and RSSI) is met. However,
# device will accept TDLS connection if it is initiated from any other peer,
# even if that peer is not configured.
#  0 - disable
#  1 - enable
# For TDLS External Control, Implicit Trigger must also be enabled.
gTDLSExternalControl=1

# Enable support for TDLS off-channel operation
#  0 - disable
#  1 - enable
# TDLS off-channel operation will be invoked when there is only one
# TDLS connection.
gEnableTDLSOffChannel=1

# Enable or Disable Random MAC (Spoofing)
# 1=Enable (default), 0=Disable
gEnableMacAddrSpoof=1

################ Datapath feature set Begin ################
# Bus bandwidth threshold values in terms of number of packets
gBusBandwidthHighThreshold=2000
gBusBandwidthMediumThreshold=500
gBusBandwidthLowThreshold=150

# Bus bandwidth compute timeout value in ms
gBusBandwidthComputeInterval=100

# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2

# VHT Tx/Rx MCS values for 2x2
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gEnable2x2=1
gVhtRxMCS2x2=2
gVhtTxMCS2x2=2

#IPA config is a bit mask and following are the configurations.
#bit0 IPA Enable
#bit1 IPA PRE Filter enable
#bit2 IPv6 enable
#bit3 IPA Resource Manager (RM) enable
#bit4 IPA Clock scaling enable
#bit5 IPA uC ENABLE
#bit6 IPA uC STA ENABLE
#bit8 IPA Real Time Debugging
gIPAConfig=0x7d
gIPADescSize=800

# Enable/Disable RX full reorder offload
gReorderOffloadSupported=1

# Enable CE classification
# 1 - enable(default)  0 - disable
gCEClassifyEnable=1

# Enable Rx handling options
# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
rx_mode=5

# Enable(Tx) fastpath for data traffic.
# 1 - enable(default)  0 - disable
gEnableFastPath=1

# This flag enables IP, TCP and UDP checksum offload
# 1 - enable(default)  0 - disable
gEnableIpTcpUdpChecksumOffload=1

# Enable TCP Segmentation Offload
# 1 - enable  0 - disable
TSOEnable=1

# Enable Generic Receive Offload
# 1 - enable(default)  0 - disable
GROEnable=1

# Enable HT MPDU Density
# 4 for 2 micro sec
ght_mpdu_density=4

# Enable flow steering to enable multiple CEs for Rx flows.
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
# Parallel Rx paths.
# 1 - enable 0 - disable(default)
gEnableFlowSteering=1

# Time in microseconds after which a NAPI poll must yield
ce_service_max_yield_time=500

#Maximum number of HTT messages to be processed per NAPI poll
ce_service_max_rx_ind_flush=1

# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
maxMSDUsPerRxInd=8

# Enable 802.11k offload
11k_offload_enable_bitmask=1

# Enable NUD tracking feature
# 1 - enable 0 - disable(default)
gEnableNUDTracking=1

# Enable PEER UNMAP CONF SUPPORT
# 1 - enable 0 - disable(default)
gEnablePeerUnmapConfSupport=1

################ Datapath feature set End ################

################ NAN feature set start ###################

# Enable NAN discovery (NAN 1.0)
# 1 - enable  0 - disable(default)
gEnableNanSupport=0
genable_nan_datapath=0

################ NAN feature set end #####################

# Beacon loss threshold
gRoamBmissFirstBcnt=10
gRoamBmissFinalBcnt=10

adaptive_dwell_mode_enabled=1

hostscan_adaptive_dwell_mode=1

adapt_dwell_lpf_weight=80

adapt_dwell_wifi_act_threshold=10

MAWCEnabled=0

drop_bcn_on_chan_mismatch=0

# Enable/Disable rtt sta mac randomization
enable_rtt_mac_randomization=1

#Enable/Disable SNR monitoring
gEnableSNRMonitoring=1

# Set IPA low/med/high bandwidth mbps
gIPALowBandwidthMbps=100
gIPAMediumBandwidthMbps=400
gIPAHighBandwidthMbps=800

mawc_nlo_enabled=0

# [VM1SOM-345][WLAN]: RF Stress Test block in Restarting
gEnableSelfRecovery=1

# P2P feature
gP2PEnabled=1

# Disable packet dump by default
gEnablePacketStats=0

################ Trace Level start ###################
########### Must add for WifiTracker usage ###########
qdf_trace_enable_wdi=65535
qdf_trace_enable_hdd=65535
qdf_trace_enable_sme=65535
qdf_trace_enable_pe=65535
qdf_trace_enable_wma=65535
qdf_trace_enable_sys=65535
qdf_trace_enable_qdf=65535
qdf_trace_enable_sap=65535
qdf_trace_enable_hdd_sap=65535
qdf_trace_enable_bmi=65535
qdf_trace_enable_cfg=65535
qdf_trace_enable_epping=65535
qdf_trace_enable_qdf_devices=65535
cfd_trace_enable_txrx=65535
qdf_trace_enable_htc=65535
qdf_trace_enable_hif=65535
qdf_trace_enable_hdd_sap_data=65535
qdf_trace_enable_hdd_data=65535
################ Trace Level end ###################

# Trigger the Neighbor Report Request sent 5s delay after the association.
nr_offload_time_offset=5

gNeighborScanChannelList=empty

gRoamScanOffloadEnabled=1

# Prefer connecting to 5G AP even if its RSSI is lower by gSelect5GHzMargin dBm than 2.4G AP, default 0(range 0~60)
# This feature requires gRoamPrefer5GHz set to 1 to take effect
#gSelect5GHzMargin=20

#Enable/Disable 5G prefer RSSI boost or penalize, 0(disabled) by default, 1(enabled)
enable_5g_band_pref=0

# Above which 5 GHz is favored, default -76(range -81~-55)
5g_rssi_boost_threshold=-76

# Factor by which 5GHz RSSI is boosted, default 20(range 0~30)
5g_rssi_boost_factor=20

# Maximum boost that can be applied to 5GHz RSSI, default 20(range 0~30)
5g_max_rssi_boost=20

# Below which 5 GHz is not favored, default -80(range -91~-65)
5g_rssi_penalize_threshold=-80

# Disable adaptive dwell mode for scanning
adaptive_dwell_mode_enabled=0

# Disable early stop scan to scan all occupied/full channel
gEnableEarlyStopScan=0

# Disable PMKSA caching to prevent full EAP authentication during roaming after 802.1X session timeout.
pmkidModes=1

# disable scoring logic in FW for candidate selection during roaming
enable_scoring_for_roam=0

# Support to start sap in indoor channel after BSP upgrade to Snapdragon_High_Mid_2017.SPF.3.0, 0.0.031.0
gindoor_channel_support=1

# Roam scan will be rejected if duration between two consecutive requests is less than this time, set to 0
# to remove this restriction
min_delay_btw_roam_scans=0


# HiRSSI related

# Sets RSSI Delta for scan trigger, default 10(range 0-16)
# Good region: -30db ~ -60db
gRoamScanHiRssiDelta=5

# set opportunity window as 30min (60 * 30000ms)

# Sets 5GHz maximum scan count, default 3(range 0-0x7fffffff)
# Note that throughput will be affected if value too big
gRoamScanHiRssiMaxCount=60

# Sets minimum delay between 5GHz scans, default 15000(range 5000-0x7fffffff)
gRoamScanHiRssiDelay=30000

# disable dense roaming in dense environment
groam_dense_rssi_thresh_offset=0

# The maximum number of software retries for preauth or reassoc
roam_preauth_retry_count=10
# Time to wait (in ms) after sending an preauth or reassoc
roam_preauth_no_ack_timeout=10

# [ASLP-2695]:To enable SAP WLAN RTT feature
gSapDot11mc=1
gfine_time_meas_cap=0x8D

#Disable adaptive dwell mode for scanning
#adaptive_dwell_mode_enabled=1

hostscan_adaptive_dwell_mode=1

adapt_dwell_lpf_weight=80

adapt_dwell_wifi_act_threshold=10

MAWCEnabled=0

drop_bcn_on_chan_mismatch=1

# Enable/Disable rtt sta mac randomization
enable_rtt_mac_randomization=1

#Enable/Disable SNR monitoring
gEnableSNRMonitoring=1

# Operating Channel List
gEnableOperatingChannelList=0
gOperatingChannelList=

# Enable/Disable force bandwidth voting during IPA suspend
gIPAForceVotingEnable=1

mawc_nlo_enabled=0

# Prefer roaming to 5GHz Bss
gRoamPrefer5GHz=1

# Prefer connecting to 5G AP even if its RSSI is lower by gSelect5GHzMargin
# dBm than 2.4G AP
gSelect5GHzMargin=5

#Skip DFS Channel in case of P2P Search
# 0 - disable (Scan DFS Channel in P2P Search)
# 1 - enable (Skip DFS Channel)
gSkipDfsChannelInP2pSearch=0

END
# Note: Configuration parser would not read anything past the END marker