# This file allows user to override the factory # defaults for the WLAN Driver # Enable IMPS or not gEnableImps=1 # Enable BMPS or not gEnableBmps=1 # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only # 7 = 11b only 8 = 11ac only. gDot11Mode=0 # Assigned MAC Addresses - This will be used until NV items are in place # Each byte of MAC address is represented in Hex format as XX Intf0MacAddress=000AF58989FF Intf1MacAddress=000AF58989FE Intf2MacAddress=000AF58989FD Intf3MacAddress=000AF58989FC # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=0 InfraUapsdViSrvIntv=0 InfraUapsdBeSrvIntv=0 InfraUapsdBkSrvIntv=0 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 #Flag to enable HostARPOffload feature or not hostArpOffload=1 #Flag to enable HostNSOffload feature or not hostNSOffload=1 # 802.11n Protection flag gEnableApProt=1 #ifndef VENDOR_EDIT #Qiulei@PSW.CN.WiFi.Power.1116749,2017/09/22 #Modify for wifi softap standby current #gEnableApOBSSProt=1 #else /* VENDOR_EDIT */ gEnableApOBSSProt=0 #endif /* VENDOR_EDIT */ #Enable/Disable UAPSD for SoftAP gEnableApUapsd=1 # Fixed Rate gFixedRate=0 # Maximum Tx power # gTxPowerCap=30 # Fragmentation Threshold # gFragmentationThreshold=2346 # RTS threshold RTSThreshold=1048576 # Intra-BSS forward gDisableIntraBssFwd=0 # WMM Enable/Disable WmmIsEnabled=0 # 802.11d support g11dSupportEnabled=0 # 802.11h support g11hSupportEnabled=1 # DFS Master Capability #ifndef VENDOR_EDIT #Guotian.Wu@PSW.CN.WiFi.Basic.SoftAP.1190360, 2019/5/23, #change for SoftAP cannot operate on DFS channel #gEnableDFSMasterCap=1 #else /* VENDOR_EDIT */ gEnableDFSMasterCap=0 #endif /* VENDOR_EDIT */ # ESE Support and fast transition EseEnabled=0 ImplicitQosIsEnabled=0 #ifdef VENDOR_EDIT #Botao.Cu@PSW.CN.WiFi.Connect.select.1064666, 2017/01/04, #add for select 5G wifi preferentially #gNeighborLookupThreshold=76 #endif /* VENDOR_EDIT */ gNeighborScanChannelMinTime=20 gNeighborScanChannelMaxTime=30 gMaxNeighborReqTries=3 # Legacy (non-ESE, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 # Check if the AP to which we are roaming is better than current AP in # terms of RSSI. Checking is disabled if set to Zero.Otherwise it will # use this value as to how better the RSSI of the new/roamable AP should # be for roaming #ifndef VENDOR_EDIT #Botao.Cu@PSW.CN.WiFi.Connect.roaming.1065694, 2016/07/06 #modify for [C18]: modify the roaming value. #RoamRssiDiff=5 #else VENDOR_EDIT RoamRssiDiff=8 #endif /* VENDOR_EDIT */ #ifdef VENDOR_EDIT #Botao.Cu@PSW.CN.WiFi.Connect.select.1064666, 2017/01/04, #add for select 5G wifi preferentially gRoamPrefer5GHz=1 gSelect5GHzMargin=5 #set roam_bad_rssi_thresh_offset_2g = 0, avoid background roaming roam from 2g to 5g # RSSI threshold offset for 2G to 5G roam roam_bad_rssi_thresh_offset_2g=0 #endif /* VENDOR_EDIT */ #Add for dense roam gtraffic_threshold=55 groam_dense_rssi_thresh_offset=0 gNeighborLookupThreshold=80 #add for roam scan diff gRoamRescanRssiDiff=3 #add for disable background scan roam roam_bg_scan_client_bitmap=0 #endif /* VENDOR_EDIT */ # To enable, set gRoamIntraBand=1 (Roaming within band) # To disable, set gRoamIntraBand=0 (Roaming across band) gRoamIntraBand=0 #Short Guard Interval Enable/disable gShortGI20Mhz=1 gShortGI40Mhz=1 #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled gAPAutoShutOff=0 #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec gWlanAutoShutdown = 0 # Not used. gApAutoChannelSelection=0 #Preferred band (both or 2.4 only or 5 only) BandCapability=0 #Channel Bonding gChannelBondingMode5GHz=1 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link #is idle for last 10 seconds.) For both active and power save clients. #Power save clients: DUT set TIM bit from 10th second onwards and till client #honors TIM bit. If doesn't honor for 5 seconds then DUT remove client. #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not #success still we try on 11th second if not tries on 12th and so on till 15th #second. Hence before disconnection DUT will send 5 NULL frames. Hence in any #case DUT will detect client got removed in (10+5) seconds. #i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and #it is period where we send NULL frame. #gApLinkMonitorPeriod = 10 #gGoLinkMonitorPeriod = 10 #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame #are succeed to send or not. Hence total effective detection time is # (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) / # (gApLinkMonitorPeriod + gApKeepAlivePeriod) gGoKeepAlivePeriod = 20 gApKeepAlivePeriod = 20 #If set will start with active scan after driver load, otherwise will start with #passive scan to find out the domain gEnableBypass11d=1 #If set to 0, will not scan DFS channels gEnableDFSChnlScan=1 # Enable DFS channel roam # 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE gAllowDFSChannelRoam=1 gVhtChannelWidth=2 # Enable Generic Receive Offload # LRO and GRO are exclusive to each other # LRO support is deprecated on latest 4.9(SDM845) kernel #ifndef VENDOR_EDIT #Rongzheng.tang@PSW.CN.WiFi.Network.1389443, 2019/05/23 #GROEnable=1 #else GROEnable=0 #endif /* VENDOR_EDIT */ #Data Inactivity Timeout when in powersave (in ms) gDataInactivityTimeout=200 # Set txchainmask and rxchainmask # These parameters are used only if gEnable2x2 is 0 # Valid values are 1,2 # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. gSetTxChainmask1x1=1 gSetRxChainmask1x1=1 # Scan Timing Parameters # gPassiveMaxChannelTime=110 # gPassiveMinChannelTime=60 #ifdef VENDOR_EDIT #Botao.Cu@PSW.CN.WiFi.Connect.Scan.958144, 2017/04/20, #Modify for enlarge scan result #gActiveMaxChannelTime=40 #gActiveMinChannelTime=20 #else gActiveMaxChannelTime=60 gActiveMinChannelTime=40 #endif /* VENDOR_EDIT */ #If set to 0, MCC is not allowed. gEnableMCCMode=1 # MCC to SCC Switch mode: # 0-Disable # 1-Enable # 2-Force SCC if same band, with SAP restart # 3-Force SCC if same band, without SAP restart by sending (E)CSA # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, # without SAP restart by sending (E)CSA gWlanMccToSccSwitchMode=3 # 1=enable STBC; 0=disable STBC gEnableRXSTBC=1 # 1=enable tx STBC; 0=disable gEnableTXSTBC=1 # 1=enable rx LDPC; 0=disable gEnableRXLDPC=1 #Enable/Disable Tx beamforming gTxBFEnable=1 #Enable/Disable Tx beamformee in SAP mode gEnableTxBFeeSAP=1 # Enable Tx beamforming in VHT20MHz # Valid values are 0,1. If commented out, the default value is 0. # 0=disable, 1=enable gEnableTxBFin20MHz=1 #Enable/Disable SU Tx beamformer support. gEnableTxSUBeamformer=1 gEnableFastRoamInConcurrency=1 #Maxium Channel time in msec gMaxMediumTime = 6000 # 802.11K support gRrmEnable=1 #Enable firmware uart print gEnablefwprint=0 # Firmware log mode # Valid values are 0,1,2 # 0=Disable, 1=WMI, 2=DIAG gEnablefwlog=1 # Maximum Receive AMPDU size (VHT only. Valid values: # 0->8k 1->16k 2->32k 3->64k 4->128k) gVhtAmpduLenExponent=7 # Maximum MPDU length (VHT only. Valid values: # 0->3895 octets, 1->7991 octets, 2->11454 octets) gVhtMpduLen=2 # Maximum number of wow filters required #gMaxWoWFilters=22 # WOW Enable/Disable. # 0 - Disable both magic pattern match and pattern byte match. # 1 - Enable magic pattern match on all interfaces. # 2 - Enable pattern byte match on all interfaces. # 3 - Enable both magic pattern and pattern byte match on all interfaces. # Default value of gEnableWoW is 3. # gEnableWoW=0 # Enable or Disable MCC Adaptive Scheduler at the FW # 1=Enable (default), 0=Disable gEnableMCCAdaptiveScheduler=1 #Enable or Disable p2p device address administered isP2pDeviceAddrAdministrated=0 # Remove Overlap channel restriction gEnableOverLapCh=0 #Enable VHT on 2.4Ghz gEnableVhtFor24GHzBand=1 #Maximum number of offload peers supported # gMaxOffloadPeers=2 # controlling the following offload patterns # through ini parameter. Default value is 1 # to disable set it to zero. ssdp = 0 # Setup multicast pattern for mDNS 224.0.0.251, # SSDP 239.255.255.250 and LLMNR 224.0.0.252 ssdp=0 #Enable Memory Deep Sleep gEnableMemDeepSleep=1 # Regulatory Setting; 0=STRICT; 1=CUSTOM gRegulatoryChangeCountry=1 # RA filtering rate limit param, the current value would not # help if the lifetime in RA is less than 3*60=3min. Then # we need to change it, though it is uncommon. # gRAFilterEnable=0 gRArateLimitInterval=600 # Maximum number of concurrent connections gMaxConcurrentActiveSessions=3 # Disable/Enable GreenAP # 0 to disable, 1 to enable, default: 1 gEnableGreenAp=0 # Radar PRI multiplier gDFSradarMappingPriMultiplier=4 gPNOScanSupport=1 #Enable/Disable LPASS support # 0 to disable, 1 to enable gEnableLpassSupport=1 # Whether userspace country code setting shld have priority gCountryCodePriority=1 # Enable(1)/Disable(0) SIFS burst gEnableSifsBurst=1 # Enable or Disable Multi-user MIMO # 1=Enable (default), 0=Disable gEnableMuBformee=1 # Enable/Disable channel avoidance for SAP in SCC scenario # 0 - disable # 1 - enable gSapSccChanAvoidance=0 # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode gIbssTxSpEndInactivityTime=10 # Enable support for TDLS # 0 - disable # 1 - enable gEnableTDLSSupport=1 # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall # initiate TDLS Discovery towards a peer whenever setup criteria (throughput # and RSSI) is met and then will initiate teardown when teardown criteria # (idle packet count and RSSI) is met. # 0 - disable # 1 - enable gEnableTDLSImplicitTrigger=1 # Enable TDLS External Control. That is, user space application has to # first configure a peer MAC in wlan driver towards which TDLS is desired. # Device will establish TDLS only towards those configured peers whenever # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS # when teardown criteria (idle packet count and RSSI) is met. However, # device will accept TDLS connection if it is initiated from any other peer, # even if that peer is not configured. # 0 - disable # 1 - enable # For TDLS External Control, Implicit Trigger must also be enabled. gTDLSExternalControl=1 # Enable support for TDLS off-channel operation # 0 - disable # 1 - enable # TDLS off-channel operation will be invoked when there is only one # TDLS connection. gEnableTDLSOffChannel=1 # Enable or Disable Random MAC (Spoofing) # 1=Enable, 0=Disable (default) gEnableMacAddrSpoof=1 ################ Datapath feature set Begin ################ # Bus bandwidth threshold values in terms of number of packets gBusBandwidthHighThreshold=2000 gBusBandwidthMediumThreshold=500 gBusBandwidthLowThreshold=150 # Bus bandwidth compute timeout value in ms gBusBandwidthComputeInterval=100 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gEnable2x2=1 gVhtRxMCS2x2=2 gVhtTxMCS2x2=2 #IPA config is a bit mask and following are the configurations. #bit0 IPA Enable #bit1 IPA PRE Filter enable #bit2 IPv6 enable #bit3 IPA Resource Manager (RM) enable #bit4 IPA Clock scaling enable #bit5 IPA uC ENABLE #bit6 IPA uC STA ENABLE #bit8 IPA Real Time Debugging gIPAConfig=0x7d gIPADescSize=800 # Enable/Disable RX full reorder offload gReorderOffloadSupported=1 # Enable CE classification # 1 - enable(default) 0 - disable gCEClassifyEnable=1 # Enable Rx handling options # Rx_thread=1 RPS=2(default for ROME) NAPI=5 rx_mode=5 # Enable(Tx) fastpath for data traffic. # 1 - enable(default) 0 - disable gEnableFastPath=1 # This flag enables IP, TCP and UDP checksum offload # 1 - enable(default) 0 - disable gEnableIpTcpUdpChecksumOffload=1 # Enable TCP Segmentation Offload # 1 - enable 0 - disable TSOEnable=1 # Enable HT MPDU Density # 4 for 2 micro sec ght_mpdu_density=4 # Enable flow steering to enable multiple CEs for Rx flows. # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. # Parallel Rx paths. # 1 - enable 0 - disable(default) gEnableFlowSteering=1 # Time in microseconds after which a NAPI poll must yield ce_service_max_yield_time=500 #Maximum number of HTT messages to be processed per NAPI poll ce_service_max_rx_ind_flush=1 # Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND maxMSDUsPerRxInd=8 ################ Datapath feature set End ################ ################ NAN feature set start ################### # Enable NAN discovery (NAN 1.0) # 1 - enable 0 - disable(default) gEnableNanSupport=1 genable_nan_datapath=1 ################ NAN feature set end ##################### #ifndef VENDOR_EDIT #Shimin.Jiang@PSW.CN.WiFi.Connect.Scan.1405517,2018/5/31 #Modify for disable adaptive dwell scan mode #adaptive_dwell_mode_enabled=1 #else adaptive_dwell_mode_enabled=0 #endif /*VENDOR_EDIT*/ hostscan_adaptive_dwell_mode=1 adapt_dwell_lpf_weight=80 adapt_dwell_wifi_act_threshold=10 enable_scoring_for_roam=1 oce_enable_probe_req_deferral=1 oce_enable_probe_req_rate=1 enable_esp_for_roam=1 ##################### Scoring Param ############### esp_qbss_score_idx7_to_4=0000000A #Add another interface while driver load gEnableConcurrentSTA=wlan1 #Enable Target Wake Time support enable_twt=0 # This ini is used to set early stop scan. Early stop #scan is a feature for roaming to stop the scans at #an early stage as soon as we find a better AP to roam. #This would make the roaming happen quickly. gEnableEarlyStopScan=1 #This ini is used to increase/decrease PCL weightage in best candidate selection. #If some APs are in PCL list, those AP will get addition weightage. pcl_weightage=0 #Currently Firmware update the sequence number for each TID with #because of security issues. But with this PN mechanism, throughput drop #is observed. With this ini FW takes the decision to trade off between #security and throughput gcmp_enabled=0 gTxBFCsnValue=4 #ifdef VENDOR_EDIT #Pan.Zhang@PSW.CN.WiFi.Basic.Log.1072015, 2017/11/23, #Add for enable Packet Log gEnablePacketLog=1 #endif /* VENDOR_EDIT */ #ifdef VENDOR_EDIT #genglin.lian@PSW.CN.WiFi.Connect.Scan.1975483, 2019/05/01, # 0 - disable # 1 - enable #Disallow the beacons/probe resp from adjacent channels allow_adj_chan_bcns=0 #Shimin.Jiang@PSW.CN.WiFi.Connect.dhcp.1037520, 2017/07/07, #Add for some ap don't response to dhcp discovery paket with qos flag equals voice arp_ac_category=0 #Yadong.Hu@Connectivity.WiFi.Connect.disconnect.956254, 2017/04/20, #Add for set value of kick out, 2047 means if DUT missed 2047 packets from AP, then disconnect gDroppedPktDisconnectTh=2047 #Add for set value of beacon miss, 10 and 20 means 30 beacon miss,then maybe trigger disconnect gRoamBmissFirstBcnt=10 gRoamBmissFinalBcnt=20 #Xiao.Li@PSW.CN.WiFi.Network.internet.1445969, 2018/06/26, #Modify for set min channel time and max channel time during SCO/eSCO gActiveMinChannelTimeBtc=120 gActiveMaxChannelTimeBtc=180 #Jie.Huang@PSW.CN.WiFi.AutoConnect.1882408 2019/03/13 #Add for : bug 1882408 do not automatically connect strong signal hotspots gEnableSNRMonitoring=0 #Yuan.Huang@PSW.CN.WiFi.Network.quality.1063633 2016/07/20, #Add for optimize download performance in noisy env. gEnableEdcaParams=0 gEdcaVoCwmin=2 gEdcaViCwmin=2 gEdcaBkCwmin=2 gEdcaBeCwmin=2 gEdcaVoCwmax=3 gEdcaViCwmax=3 gEdcaBkCwmax=3 gEdcaBeCwmax=3 gEdcaVoAifs=0 gEdcaViAifs=0 gEdcaBkAifs=0 gEdcaBeAifs=0 #Rongzheng.tang@Connectivity.Wifi.Network.1063609, 2017/03/30, #Add for enable PER based roaming # enabled for Tx and Rx traffic gper_roam_enabled=3 # Mbps x 10 gper_roam_high_rate_th=540 gper_roam_low_rate_th =150 # high PER rate % for roaming scan triggered gper_roam_th_percent=80 gper_roam_rest_time=60 #Yuan.Huang@PSW.CN.WiFi.Network.internet.1064218, 2016/08/04, #Modify for QQ message delays when DUT is asleep rx_wakelock_timeout=250 #endif /* VENDOR_EDIT */ #Rongzheng.tang@Connectivity.Wifi.Network.1031774, 2017/06/18 #Add for disable active mode offload. gActiveModeOffload=0 #Wei.Wang@PSW.CN.WiFi.Network.quality.1170942, 2017/12/04, #disable qpower,to decrease ping delay and improve download speed gEnablePowerSaveOffload=2 #else /* VENDOR_EDIT */ #gEnablePowerSaveOffload=1 #ifdef VENDOR_EDIT #Qiulei@PSW.CN.WiFi.Power.1067360 2016/08/08 #Add for : wifi hongbao ,Enable Host driver and above layers control the PS mechanism isAndroidPsEn=1 #endif /* VENDOR_EDIT */ #ifdef VENDOR_EDIT #Qiulei@PSW.CN.WiFi.Hardware.1132176, 2017/03/07 #Add for 2.4G&5G MIMO config,2.4G SAP SISO gVdevTypeNss_5g=21930 gVdevTypeNss_2g=21930 #endif /* VENDOR_EDIT */ #ifdef VENDOR_EDIT #Qiulei@PSW.CN.WiFi.Hardware.1065440, 2017/05/16 #Add for show the max linkspeed gReportMaxLinkSpeed=1 gChannelBondingMode24GHz=0 #endif /* VENDOR_EDIT */ #ifdef VENDOR_EDIT #Qiulei@PSW.CN.WiFi.Power.802254, 2016/07/20 #Add for reduce ap sleep current gApLinkMonitorPeriod = 25 #endif #ifdef VENDOR_EDIT #Min.Yi@PSW.CN.WiFi.Hardware.Power.1323750, 2018/03/21 #Add for high current when download on 11B g11bNumTxChains=1 #endif /* VENDOR_EDIT */ #ifdef VENDOR_EDIT #Guotian.Wu@PSW.CN.WiFi.Hardware.OpCustomized.1123073, 2019/07/02 #disable for CTS test fail gEnableRTTSupport=0 #endif /* VENDOR_EDIT */ #Yuan.Huang@PSW.CN.WiFi.Network.internet.1140781, 2017/11/03, #Add for data stall detection gEnableDataStallDetection=0 #endif /* VENDOR_EDIT */ #ifndef VENDOR_EDIT #Tao.Hui@PSW.CN.WiFi.Basic.Custom.1067549, 2018/01/02, #Modify for country code JP soft ap cant got 5G list for bug:1194908 gindoor_channel_support=1 #endif /* VENDOR_EDIT */ #Yuanliu.Tang@PSW.CN.WiFi.Basic.Crash.1135753, 2017/05/27 #Add for open walkround feature to avoid MTK AP crash,QC case2952499 gForce1x1Exception=1 #endif /* VENDOR_EDIT */ #ifdef VENDOR_EDIT #Tao.Hui@PSW.CN.WiFi.Basic.Custom.1884719 2019/03/08 #add for bdf fw rus gEnableForceTargetAssert=1 #endif /* VENDOR_EDIT */ #ifndef VENDOR_EDIT #Guotian.Wu@PSW.CN.WiFi.Basic.SoftAP.1181662, 2019/05/31, #fix EU JP band1 band4 issue etsi_srd_chan_in_master_mode=1 #endif /* VENDOR_EDIT */ # etsi13_srd_chan_in_master_mode - Enable/disable ETSI SRD channels in # master mode PCL and ACS functionality # @Min: 0 # @Max: 1 # @Default: 0 etsi13_srd_chan_in_master_mode=1 ignore_fw_reg_offload_ind=1 END # Note: Configuration parser would not read anything past the END marker